Just How to Install a Bathtub in Your Bathroom
Just How to Install a Bathtub in Your Bathroom
Blog Article
Just about everyone will have their own unique thinking when it comes to Tools You Need to Install a New Bathtub .
Installing a tub isn't precisely brain surgery, yet it does call for solid plumbing, woodworking, and also in some cases, tiling skills. Changing an old tub with a brand-new one is likewise a moderately tough project. If the old tub is easily easily accessible, the task can relocate speedily; if you need to open up a wall surface to get rid of the old bathtub and position the new tub, the job is a lot harder. In either situation, the job is within a residence handyman's abilities, although you will certainly require an assistant to leave the old bathtub as well as embeded in the brand-new one. Make certain you have qualified yourself for the job and are comfortable trying it. As opposed to working with a contractor to take control of a halfway-completed task, it is far better to consider utilizing one before you begin. Possibilities are you might require an expert plumber to make tube connections.
This short article will assist you set up a new bathtub in your washroom if you have actually already bought a brand-new bathtub as well as don't need to change the setup of your previous water pipelines.
Your tools and product list must comprise the following:
Preparing for the Installment
To start with, the sustaining framework supplied with the bathroom must be fitted (if needed) according to the maker's instructions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to see to it that if the faucet includes a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps device to avoid strain on the bath tub.
Fit the versatile faucet ports to the bottom of both faucets using 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to now prepare to be suited its final placement.
Removing Old Taps
If you need to change old taps with new ones as a part of your installment, then the first thing you must do is separate the supply of water. After doing so, switch on the taps to drain pipes any kind of water remaining in the system. The process of getting rid of the existing faucets can be rather troublesome as a result of the restricted accessibility that is frequently the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the taps. Have a fabric all set for the remaining water that will originate from the pipelines. Once the supply pipelines have been eliminated, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from transforming throughout this procedure. As soon as the taps have been removed, the holes in the bath/basin will have to be cleaned up of any kind of old securing compound.
Prior to moving on to fit the new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.
Mounting the Bath tub
Using the two wooden boards under its feet, place the tub in the needed setting. The wood boards are handy in equally spreading out the weight of the bathtub over the area of the boards instead of concentrating all the weight onto 4 tiny factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by examining the level and adjusting the feet on the bathtub until the spirit level reads level.
To install taps, fit the bottom of the furthest flexible faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the very same for the other tap.
Activate the water as well as inspect all joints and brand-new pipework for leakages as well as tighten them if required. Fill the bath tub as well as likewise examine the overflow outlet and the regular electrical outlet for leaks.
Finally, deal with the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bath tub should wait till the tub has been made use of a minimum of once as this will certainly settle it into its last setting.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end offers a connection to the existing supply pipes.
If you require to fit a monobloc, then you will need reducing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washers remain in location in between the tap and also the sink. Protect the faucet in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap adapters. The former kind must be connected to the faucet ends initially, tightening just by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the location where the bath satisfies the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate enough to crack a stiff seal, creating the water to permeate the wall surface in between the bathroom as well as the tiling, bring about complications with moisture and also feasible leaks to the ceiling listed below.
You can select from a range of coloured sealers to assimilate your fixtures as well as fittings. They are offered in tubes and cartridges, as well as can sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of soaked paper or soft rope. Remember to always load the bathtub with water before securing, to allow for the motion experienced when the bathtub is in use. The sealer can crack fairly early if you do not think about this movement before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily available on the market. It is a good idea to fit the floor tiles using water-resistant or water-proof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm certainly very fascinated with Tools You Need to Install a New Bathtub and I hope you liked the blog posting. Sharing is caring. Helping people is fun. Many thanks for taking the time to read it.
Go Deal Report this page